What amp settings does Brian may use?
What’s Brian May’s guitar amp settings? Early in the video, Brian shows the amp he is using and importantly demonstrates the sound without and then with the treble booster. Brian always uses one of the two input channels on a Vox AC30, namely the “Normal channel”.
How do you make an amp sound like Nirvana?
The Quick Answer. To get Nirvana’s tone with your amplifier, have the treble and mids fairly high (around 7-8) and the bass on around 5 to begin with. The distortion should be quite high for the chorus (usually between 8-10), unless you’re using a pedal.
How do I get the blues tone on my amp?
How to Set Up Any Amp for Blues
- Make sure your guitar’s volume and tone controls are on maximum.
- Set the volume to a comfortable level.
- Select the overdriven channel (unless you are using a pedal).
- Set the gain to 3, the treble and mids to 7, and the bass to 3.
- Turn off reverb and any other effects.
What amp did Queen use?
VOX AC30’s
Queen. “VOX AC30’s have been a part of my life and work for 40 years now, and they always give me exactly what I need in terms of sound; I have no need to look elsewhere.” A diehard VOX fan since the late 1960s, Brian May has relied on AC30s to provide his signature sound throughout his entire career.
What tuning does Queen use?
The track is even played in a drop D tuning featuring some double stops and single-note riffing. It’s definitely got a bit more twang than the majority of their songs but if you want to try it out yourself, go here.
How does Brian May get his guitar sound?
His most revered tone comes from a treble booster, a number of Vox AC30s that are turned up full and the Red Special’s bridge and middle pickups switched together in series and in phase; that’s the guitar sound that’s graced every single Queen album and every gig Brian’s participated in since 1966.
What does Brian May effect?
The only real effects May uses is his Fryer Treble Booster mounted on his guitar strap, a Dunlop rackmounted wah, and a pair of TC Electronic G-Major 2 delay units (one set to 800 ms and the other 1600 ms).
How does Brian may get his guitar sound?
What was Kurt Cobain amp settings?
He preferred a smoother low-end with boosted mids and highs. That means you want to set your bass to just above halfway. Both the mids and treble will then be dialed almost all the way to max. And since Kurt used pedals to boost his sound, the amp should be on the clean channel with the gain and reverb turned down.
What AMP should I use for a Killer Queen solo?
You can hear that there is quite a bit of mid range and bottom end in the Killer Queen solo and the drive is considerably more than what comes from a standard Vox AC-30 amp – so I’d start by boosting the Bass and Mid range, and put the gain to full. 4. The Effects
How can I sound like Brian May with Queen?
Queen’s guitar tone was usually overdriven and had moderate to high treble to give it more presence. The bass and mids should also be moderately high to smooth out any harshness. It is very difficult to give a one-size-fits-all amp setting preset to sound like Brian May for a couple of reasons. 1. It really depends what rig you’re using.
What AMP does Brian Wilson use for Killer Queen?
In this case Brian uses a Vox AC-30 so we select the ‘Combo’ Amp setting. You can hear that there is quite a bit of mid range and bottom end in the Killer Queen solo and the drive is considerably more than what comes from a standard Vox AC-30 amp – so I’d start by boosting the Bass and Mid range, and put the gain to full.
What amp settings should I use for we are the Champions?
Here are the amp settings to start with for “We Are The Champions”. This song also has a smoother overdriven tone, compared to a grittier sound. You should increase the mids and bass to again smooth out the treble, and avoid having the overdrive/gain too high to prevent it sounding too crackly.